Due to high temperature, large sulfur content and difficult operation and maintenance of industrial boiler bag dust collector, it has always been a big problem for environmental protection industry. According to years of working experience, our company has developed 35T boiler dust collector with large air volume, good effect, low power consumption, stable equipment and small maintenance workload
35T boiler dust collector product introduction:
1, our company developed industrial boiler using bag filter chamber stop pulse wind blowing ash removal technology, overcome the conventional pulse dust catcher and chamber the disadvantage of counter blowing dust, soot cleaning ability, high dust removal efficiency, low emission concentration, air leakage rate is small, less energy consumption, less consumption of steel, covers an area of less, stable and reliable operation, good economic benefit, is suitable for metallurgy, building materials, cement, machinery, Industry, power, light industry dust gas purification and material recovery.
2. The purpose of ash removal can be achieved by spraying once, so the ash removal cycle is prolonged, the energy consumption of ash removal is reduced, and the consumption of compressed air can be greatly reduced. At the same time, the fatigue degree of filter bag and pulse valve is correspondingly reduced, so as to multiply the service life of filter bag and valve plate.
3. The maintenance and bag change can be carried out in separate rooms under the normal operation conditions of non-stop fan and system. The opening of the filter bag adopts elastic expanding ring, which has good sealing performance and is firm and reliable. The filter bag keel adopts polygonal shape, which reduces the friction between the bag and the keel, prolongs the life of the bag, and is easy to unload the bag.
4. Adopt the upper bag pumping method. After pulling out the skeleton when changing the bag, the dirty bag is put into the lower gray hopper of the box body and taken out from the manhole, which improves the operating conditions of changing the bag.
5, the box adopts air tightness design, good sealing, inspection door with excellent sealing material, air leakage rate is very low.
6, inlet and outlet layout is compact, airflow resistance is small.
7. The dust collector is equipped with heat preservation device to prevent the flue gas condensation at too low temperature.
4.2 related technical parameters of dust collector design :(see attached drawings for external dimensions)
1. Installation boiler capacity of this project: 50T/H×2
2, dust collector inlet smoke volume: 300000m3/h
3, dust concentration of imported dust collector: 25~30g/m3
4, dust collector outlet emission concentration: <50mg/m3
5, the normal working temperature range of flue gas: 140~170℃
6, the filter area of dust collector: 4630m2
7, filtration wind speed: 0.7~1.9m/min
8, dust collector filter material: PPS filter material
9, dust collector operation of the total resistance: 1200-1500Pa
10, dust collector body air leakage rate: <3%
11, dust collector shell design pressure: static +5000Pa,-6500Pa
4.3 Performance parameters of filter material
According to the actual working conditions and practical experience of your unit, we recommend the use of PPS (polyphenylene sulfide) filter material, PPS filter material has high temperature resistance and good acid and alkali corrosion resistance performance, suitable for dust removal of coal flue gas. Its technical parameters are as follows:
PPS filter material
Continuous operating temperature (° C) ≤190 ° C
Short-time operating temperature (℃) 220℃
Acid optimal
Alkali resistance of optimal
Wear resistance of optimal
Oxidizer in general
Excellent hydrolysis stability
Flame retardant optimal
4.4 Solenoid valve: working pressure: 0.25-0.5mpa Working medium: clean air
Voltage: DC24V Current: 0.8A
Use environment: temperature -10℃~55℃, air relative temperature does not exceed 85%
Service life: 1 million times
Quantity: 128 PCS
Compressed air consumption: 3~4m3/h
4.5 Control System
The electrical control device is controlled by PLC program. With automatic and manual control modes, the control program can be adjusted on site to change the pulse blowing cycle (T-0.1~90s).
4.6 Scope of Supply:
1. Upper, middle and lower boxes of equipment, ladder climbing and guardrail.
2. Filter bag φ 160×6000mm, quantity: 1536;
3, skeleton φ 155×5970mm, quantity: 1536;
4, cylinder lifting valve: φ 650, quantity 16 sets, Tianjin pneumatic components
5, electromagnetic pulse valve: 3 "submerged valve, 128
6, star unloader: YJD-26A, 8 sets
7. PLC electric control system: 1 set
8, insulation material: rock wool
9. Equipment assembly drawing, qualification certificate of supporting equipment, and a copy of random data
4.7 Supply cycle: the goods will arrive within 45 days after the contract signing.